AMMCO 7000 PDF

View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.

Author: Shakus Kagazragore
Country: Nigeria
Language: English (Spanish)
Genre: Automotive
Published (Last): 6 September 2005
Pages: 44
PDF File Size: 5.80 Mb
ePub File Size: 1.93 Mb
ISBN: 635-5-20101-491-4
Downloads: 95645
Price: Free* [*Free Regsitration Required]
Uploader: Torisar

Choose one of the inner grooves when machining medium duty truck rotors. Any excessive wear or deformity should be noted and, if not within amjco limits, the rotor should be replaced.

Table Of Contents Cleaning Now engage the automatic cross feed by moving the knobFig. Installation Replace or repair damaged or worn cords immediately soon as it is amkco. If any of the goods called for amnco this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. Brake Lathes Care of Arbors and Adapters CAUTION Although the adapters, arbors, and the spindle are made of top grade steel and are turned, hardened, and precision ground to close tolerances, great care should be taken in their use, handling, and storage.

Unplug unit from power source before servicing or adjusting. Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Move the belt to the pulley groove that will give the correct spindle speed for the cut to be taken, Fig.

Automotiv e Ser vice Equipment and T ools. DO NOT throw them into a box. Don’t have an account? Don’t show me this message again. Identify the hazard levels used in this manual with the following definitions and signal words: Make sure that the tool bits clear the rotor faces and the silencer band. Use the outer pulley groove for all passenger car and light truck rotors, Fig. Tell us what’s missing.

  2009 KAWASAKI NINJA 650R OWNERS MANUAL PDF

The patented self-aligning spacer prevents diagonal thrust on the adapters. Page 4 Safety Safety Notices and Decals For your ammci, and the safety of others, read and understand all of the safety notices and decals included here and on the unit. Read entire manual before installing, operating, or servicing this equipment. Move the tool bits inward until they just contact the faces of the rotor.

AMMCO 7000 Installation Instructions Manual

READ these instr uctions bef ore placing unit in. KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators. Reconditioning Disc Brake Rotors The patented self-aligning spacer prevents diagonal thrust on the adapters.

Also review the following general safety instructions. Give the rotor a full turn by hand and start the lathe. Page 15 Examine each adapter and the arbor for nicks, burrs, chips, dirt, and rust.

Safety Notices And Decals For additional copies of either, or further information, contact: Adjust the drive belt to match the rotor size. Recheck the setting of the depth-of-cut collars which were on zero.

Do this for your own protection.

AMMCO Hustler Disc Brake Lathe Operation Manual | eBay

Clean, repair, remount, or replace as necessary. Enter ammci from picture: Brake Lathes Maintenance and Service Note: Page of 20 Go. The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. After the brake rotor is mounted on the arbor, install the silencer band. Either rough or finish cuts may be taken to resurface a rotor.

  KUMPULAN PUISI SAPARDI DJOKO DAMONO PDF

What’s missing? Tell us about it.

Warning This equipment incorporates parts such as snap switches and power receptacles which tend to produce arcs or sparks. Comments to this Manuals Your Name. KEEP these and other materials delivered.

Remove all adapters from the arbor after machining am,co rotor and wipe them clean – especially the inboard adapter. Also inspect the rotor hub for loose or damaged bearing cups. Replace or repair damaged or worn cords immediately soon as it is received.

Generally, finish cuts should be. Or point us to the URL where the manual is located.

Handle the adapters and arbors with care and store them on individual hooks. Reset the collars if necessary. Cutting or grinding on an exposed sur- face such as a rotor will produce flying chips. Keep bystanders out of work area.

AMMCO INSTALLATION INSTRUCTIONS MANUAL Pdf Download.

Turn each tool bit control the outer knurled knobs clockwise until the tool bits just contact the rotor faces. Turn the outer knurl of the twin cutter control left and right to check for a smooth, free movement. Brake Lathes Cross Feed – The cross feed draws the twin tool bits across the face of a brake rotor when the cross feed drive is engaged. Use a face shield and dust mask during dusty operations. When the cross feed has moved the cutting tools all the way across the face of the rotor, the feed will shut off automatically.

Page 14 Brake Lathes 4.