BRITISH STANDARD BS EN ISO Incorporating Corrigendum No. 1 Fasteners — Quality assurance system The European. Find the most up-to-date version of ISO at Engineering We are looking ISO , it was referenced in a document. The statement that can be found on it is: ISO specifies requirements for a fastener q.
|Published (Last):||1 January 2012|
|PDF File Size:||20.56 Mb|
|ePub File Size:||14.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. In such cases, depending on the type and geometry of the fastener, corrosion resistance is based on significant surfaces of the fastener.
Contact the Information Centre. For dated references, subsequent amendments to or revisions of any of these publications apply isl this European Standard only when incorporated in it by amendment or revision. In case of dispute, the supplier shall be able to provide all necessary information relating to the manufacturing lot number.
ISO – Fasteners — Quality assurance system
The distributor shall be able to provide full manufacturing lot documentation for a ten year period from the date of the sale to the customer, provided the customer gives the ixo lot is or the trace number to the distributor. The corresponding tolerances are specified considering the individual part and production method.
Users are responsible for its correct application. It is incorporated by Royal Charter. This International Standard outlines the requirements from receipt of raw material through the manufacturing process to delivery at the distributor or the user, who is the installer.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
For undated references, the latest edition of the normative document referred to applies. The quality objective, zero defects, cannot be realized with today’s state-of-the-art methods. Experience has shown that for one single specified characteristic, after automatic inspection there is still an average remaining level of non-conformities of about. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.
Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. The adherence to such a specification e.
BS EN ISO Fasteners — Quality assurance system – MBA智库文档
Users of British Standards should make sure that they possess the latest amendments or editions. Proceed to Checkout Continue Shopping. Various BSI electronic information services are also available which give ios on all its products and services.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. The work of preparing International Standards is normally carried out through ISO technical committees.
Standards Subsctiption may be the perfect solution. The BSI copyright date displayed in this document indicates when the document was last issued.
It presents the UK view on standards in Europe and at the international level. As the voice of the U. Already Subscribed to this document. Need more than one copy? The order shall designate the selected product characteristics, if any, considering the intended application, or a reasonably foreseeable application and its consequence. Your Alert Profile lists the documents that will be monitored.
BS EN ISO 16426:2002
In addition, the parts are transferred into other vessels many times during the production process, the number of transfer operations depending on the length of the production chain e. If the user considers that the isso to which the characteristic s deviate s from specified requirements will have no significant effect on the assembly or performance of the fasteners in their service application, the user may authorize a written release of the fasteners for completion of production or for shipment, as applicable.
While unsystematic non-conformities cannot be recognized by statistical process control SPCsystematic non- conformities can usually be limited by the application of SPC. Special measures are taken to prevent mechanical damage especially at points of impact and to avoid contamination. It is common practice to include only fasteners with non-conforming characteristics and dissimilar fasteners in the establishment of ppm values unless otherwise agreed.